Product Index >>

All Products (1996 of 4308)Rocket Vision Brand Products

Rocket Vision - Mach Buster

Attributes

Center Of Pressure:		10.78 inches from front (Rocksim/Rocksim)
Manufacturer:		Rocket Vision

Reviews

• Rocket Vision - Mach Buster By Terry Moore-Read
• Rocket Vision - Mach Buster By Terry Moore-Read
• Rocket Vision - Mach Buster By Terry Moore-Read
• Rocket Vision - Mach Buster By Terry Moore-Read

Rocket Gallery

• Alex Zoghlin's Mach Buster
• Ron Watkins's Rocket Vision Mach Buster
• Kevin Rezac's Rocket Vision Mach Buster
• David Urbanek's Rocket Vision Mach Buster
• Paul Gray's Rocket Vision Mach Buster
• Ben Snider's Rocket Vision Mach Buster
• Steve Jensen's Rocket Vision Mach Buster
• Casey Smith's Rocket Vision Mach Buster
• Russell Taragan's Rocket Vision Mach Buster
• Dick Stafford's Rocket Vision Mach Buster

What You Can Do

• Submit a Review of this Product
• Update This Product's Information
• Upload an Image of This Product
• Upload a Rocksim Design File of This Kit
• Share a Video of This Product
• Suggest a Link Related to This Product
• Add CP Information for this Kit

Flight Log

Date	Rocket Name	Motor(s)	Altitude	Notes
1998-09-19	David Urbanek's Rocket Vision Mach Buster	G55-10	-	Took off almost in cruise missile mode. Launch rod was whipping back and forth. Rocket tried to...
1998-09-19	David Urbanek's Rocket Vision Mach Buster	D12-7	-	Took off at an angle. Didn't know why. Launch lug seemed a bit tight.
1998-09-20	David Urbanek's Rocket Vision Mach Buster	D12-7	-	Replaced lug with 1/4 lug. Perfectly straight boost.
1998-09-20	David Urbanek's Rocket Vision Mach Buster	F72-10	-	Nose cone seperated under full boost. Looked like motor failure. Sheared the kevlar shock cord....
1999-08-15	Dick Stafford's Rocket Vision Mach Buster	D12-7	-	nice high flight, angled a bit into the wind, recovery ~100 ft from pad
1999-09-06	Ron Watkins's Rocket Vision Mach Buster	D12-7	-	Poor flight-considerable weathercocking on lift-off-predicted altitude-1,000 ft. -rocket drifted...
2000-02-09	Russell Taragan's Rocket Vision Mach Buster	F101-10	-	The flight was very fast! (0 to 850 mph in . 8 sec. ) Rocket was tracked all the way to ground via...
2000-03-18	Dick Stafford's Rocket Vision Mach Buster	G55-10	-	bang!. . . . and it was gone. . . .
2000-04-30	Russell Taragan's Rocket Vision Mach Buster	F101-10	-	Fast (probably supersonic) flight, tracking chalk visible just below 5000+ ft. clouds but rocket...
2000-06-20	Ben Snider's Rocket Vision Mach Buster	D12-7	-	took off to about 75ft. then in a single motion went horizontal just slightly upward about 1000ft....
2000-09-17	Paul Gray's Rocket Vision Mach Buster	D12-5	-	Good flight but weathercocked a fair bit. Good revoery though. Have F72 motor for flight once in a...
2000-09-20	Paul Gray's Rocket Vision Mach Buster	D12-5	-	Good flight but again weathercokced overthe farm fild nearby. Chute tangled and so came down fast...
2000-09-29	Paul Gray's Rocket Vision Mach Buster	E15-7	-	WOW! This thing got up and went! Wish i had the f72-10 engine that i am still waiting to get in...
2000-10-23	Ben Snider's Rocket Vision Mach Buster	C6-5	-	went up straight for about 200ft then started a corkscrew through motor burnout to about 500ft....
2000-11-25	Kevin Rezac's Rocket Vision Mach Buster	F101-15	-	Loved this flight. Used 18ft of reflective streamer and found it right in the middle of a farm...
2001-03-30	Casey Smith's Rocket Vision Mach Buster	D12-3	-	Nice boost, did not want to lose it. It flies great. Nice streamer recovery.
2011-04-17	Alex Zoghlin's Mach Buster	CTI F240	-	Can't say much about the flight. Went so fast, I didn't even see it leaving the pad.

- Link to this Page -

You can link to this page using the following HTML or BB Code.

Text Link in HTML (for web sites)

<a href="http://www.rocketreviews.com/mach-buster---rocket-vision.html">Rocket Vision - Mach Buster</a>

Text Link in BB Code (for forum posts)

[url=http://www.rocketreviews.com/mach-buster---rocket-vision.html]Rocket Vision - Mach Buster[/url]

Select the appropriate above text with your mouse then "right-click" and select "Copy." Then, paste the text into your web site's code or a discussion forum post.