Hawk Mountain Enterprises Raptor

Hawk Mountain Enterprises - Raptor

Contributed by Jack Caynon

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar
Overall Rating: starstarstarstarstar_border
Hawk Mountain Raptor

Brief:
At the foot of the northern slope of Hawk Mountain sits the quiet hamlet of New Ringgold, Pennsylvania, an unlikely aerie for the fabulous fiberglass rockets of Hawk Mountain Enterprises. The fledgling of this flock of birds is the Raptor, an all fiberglass 29mm high power rocket capable of supersonic flights with large H and 29mm I motors.

Construction:
The Raptor is the smallest (49 inches long) and least expensive Hawk Mountain rocket. As is the case for all Hawk Mountain kits, the airframe is completely made of spiral wound fiberglass. It is almost, but not quite a minimum diameter rocket. There are several options available for the kit but I only chose two of them. The kit came with:

  • 1 42in long 1.3in diameter G-12 airframe fin slots precut
  • 3 0.093in G-10 Fins, already shaped
  • 1 29mm fiberglass motor mount (optional)
  • 1 29mm Slimline retainer (optional)
  • 1 24in X-form Chute
  • 1 fiberglass piston w/ bulkhead
  • 1 Fiberglass nose cone
  • 2 Acme 2in conformal launch lugs
  • Kevlar® shock cord with a Quick-Link...etc.

One option I did not purchase was the 8in payload section. You may want to buy the payload section if you intend to use dual deployment electronics. The piston is a new feature for this kit, too. It was added to avoid recovery system failures caused by heat shields getting stuck in the airframe during the recovery phase of the flight.

I ordered the kit via a telephone call to Hawk Mountain Enterprise's owner, Alan Gorecki. Alan is a very pleasant fellow and is happy to answer any questions about his kits during a telephone call.

I will make several suggestions at the start. If you don't have a Dremel tool, get one and purchase the 60 grit sanding drums. You must rough up the fiberglass surfaces that will be epoxied and the Dremel tool will make your life so much easier. You'll also need to have J.B. Weld epoxy on hand along with the regular epoxy you may have if you decide to use the Slimline motor retainer (if you go with the Aeropack retainer, the same advice applies).

Hawk Mountain Raptor The kit arrived promptly and was packaged well in a sturdy cardboard box. If there is one area of improvement I could find, it concerns the instructions--they're sparse and not written with the novice rocketeer in mind. Indeed, there is one step in the instructions that is out of sequence, concerning the shock cord attachment to the motor mount tube. First, if you purchased the Slimline motor retainer, install that on the motor mount per the Slimline directions. Make certain to use the 600 degree J.B. Weld epoxy to attach the retainer to your motor mount. Then prepare the motor mount tube for installation in the airframe. However, before you epoxy the Kevlar® shock cord onto the motor mount, skip ahead in the instructions to the piston assembly. Assemble the piston, wait for the epoxy to dry, then slip the aft end of the shock cord through the hole in the piston bulkhead until you reach the knot at the 10ft spot on the shock cord. Epoxy the knot to the hole in the piston. Then, when that's dry, go ahead and epoxy the aft end of the shock cord to the motor mount tube. Do not use J.B. Weld epoxy to mount the shock cord; that type of epoxy will not penetrate the weave of the shock cord and adequately attach the cord to the fiberglass tube.

Hawk Mountain Raptor One modification that I made to ensure a strong fin attachment to the airframe is to purchase some 1/2in Kevlar® tape and cut six strips to fit the root edge for each side of the three fins. By epoxying the tape in each fin joint, the attachment points to the airframe are greatly strengthened. First apply some epoxy to the joint, then press a piece of tape into the joint. Use a popsicle stick to fold the tape so half of it is on the airframe and half on the fin. Then cover the tape with more epoxy. Since this rocket has a 24 inch X-fo rm parachute, it recovers quickly and the tape should go a long way to help avoid having a fin pop off when the rocket lands. This made the fins quite solid and I was very pleased with the result.

At this point, all you need to do is add your chute, assemble your nose cone by epoxying the nose cone bulkhead into the base of the nose cone--it's the one with the screweye attached for you, and attach your launch lugs to complete the construction. The rocket goes together quickly. The most time consuming part is waiting for the J.B. Weld epoxy to totally dry (about 15 hours).

Finishing:
Before you prime the rocket, you should wet sand it with 320 grit wet/dry sanding paper. Wipe any sanding residue off the airframe and nose cone after sanding, then prime. I used Duplicolor gray sandable primer on this rocket. I sanded the first two coats with 320 grit and wet sanded the final coat with 400 grit wet/dry paper. Since I'm using fluorescent paint for the final coat, I had to put down a white undercoat on top of the gray primer. After the undercoat dried, I painted the nose cone and one fin flat black and the rest of the airframe fluorescent red-orange.

Construction Rating: 4 out of 5

Hawk Mountain Raptor

Flight:
On October 12, 2003, I flew the Raptor at Nike Carrollton Park located in Smithfield, Virginia. For her maiden flight, I launched the Raptor on a F40-10W. The lift off was slow and majestic as the rocket accelerated and flew into the sky straight as an arrow. After reaching about 1500 feet, the rocket landed near the launch pads. The piston system worked perfectly.

I decided to go for broke and launched the Raptor on an H128-10W motor. This is where I encountered a problem. Because I followed the Slimline motor retainer manufacturer's instructions to the letter during construction, my Dr. Rocket 29/180 aft closure would not fit in the motor mount and allow me to use the retainer's snap ring. I decided to go for it anyway and try to use masking tape to friction fit the casing. The rocket screamed off the pad, nearly going supersonic. This time the rocket reached around 4000 feet and recovered about 200 yards from the launch pad. Unfortunately, the 200 yards was in the middle of a cotton field, so after trudging through the crop, I was able to recover the rocket. However, the casing was gone.

Never to be accused of leaving well enough alone, I decided to fly her one more time. This time, I put a single use G40-10W motor in her, thinking the rocket would go about 2500 to 3000 feet or so. Again, the Raptor streaked into the sky, like a bat-out-of-hell. It easily passed the 3000 foot mark...and kept going. Finally, the chute was ejected but the rocket must have caught a thermal, drifting far beyond the point of the H motor landing and continued to ride it over some trees in the distance. After an hour of fruitless searching, I couldn't find her.

Recovery:
With the piston system and the Kevlar® shock cord, no wadding is needed.

Flight Rating: 5 out of 5

Summary:
This rocket is a work of art and as long as it doesn't come in ballistic, it will survive. The Raptor is a fabulous bargain considering its ruggedness and features in comparison to the price. The base price for the Raptor is $65.00. With the two options I purchased, there was an additional cost of $24.35. However, there are several things I'd change for the next go around. I simply do not like the Slimline motor retainer. It is vitally important to fit your motor casing before you glue the retainer in place. I never had that problem with the Aeropack retainer, which simply screws on/screws off, versus fumbling with the Slimline's snap ring, so I will opt to go with Aeropack for the next Raptor. In addition, I think the 24in X-form chute is still too much chute for this rocket and will lead to it getting lost. I'd suggest going down to an 18 inch x-form or a 15 inch regular chute especially if you follow my suggestion to reinforce the fins with kevlar® tape. Heck, you may even want to use a streamer, since this thing is so tough.

With a few modifications, you can own a virtually invulnerable rocket that is capable of supersonic flight on large H and I motors, flies beautifully on F and G motors, and stand a good chance of bringing it home at the end of the day.

Overall Rating: 4 out of 5

Other Reviews
  • Hawk Mountain Enterprises Raptor By Alex Bellenie (August 7, 2007)

    Brief: The Hawk Mountain Raptor is a near minimum diameter high-performance rocket kit with all fiberglass components, Kevlar shock cord, pre-cut and pre-beveled fins, pre-slotted airframe, and thru-the-wall fin mounting. This sky-puncher can fly on E-I power! Construction: When I ordered this kit, it came on time and packaged in a 4’ x 4” x 4” box with packaging ...

Flights

Comments:

avatar
D.G.L. (November 10, 2003)
I just bought a Hawk Mtn Raptor from a vendor friend. He built his with the standard Aero Pack motor retainer instead of the Slimline that the reviewer above used. The problem is, the screw-on ring of the standard Aero Pack motor retainer sticks out too far from the body tube, and actually interferes with the launch rod. My friend had to grind off some of the screw-on ring to keep it from contacting the rod. It look hideous, but it works. For my Raptor, my friend advised me to get the Slimline motor retainer. I have used the Slimlines for various PML rockets with no problems. The secret is to actually pop in my RMS motor casing (with the rear closure on) to make sure that it will work. Any J.B. Weld epoxy that squeezes on to the rear closure or casing can be quickly wiped off. The Slimline motor retainer won't interfere with the launch rod, and it's MUCH MORE AERODYNAMIC than the standard Aero Pack retainer. If you want to go HIGH and FAST with a TOUGH, 29mm rocket, this is the one!

comment Post a Comment