Estes Maxi Alpha III

Estes - Maxi Alpha III {Kit} (001903, 1321) [1979-1985,2000,2011-]

Contributed by Mike Caplinger

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Published: 2016-06-01
Diameter: 2.60 inches
Length: 33.25 inches
Manufacturer: Estes
Skill Level: 2
Style: Sport

Brief

The Estes Alpha, designed by Bill Simon and introduced in 1967, is the prototypical 3FNC that has introduced generations of rocketeers to the hobby.  The original Alpha, of course, had a balsa nose cone and fins.  The Alpha III (1971) was an easier-to-build plastic version with a one-piece molded fin can assembly.  Estes has released several larger versions of the Alpha design, the largest being the 2.6" diameter Maxi Alpha 3, which made its first appearance in 1979 and has been in and out of production since.  I bought mine in a 50%-off Estes special in late 2015.

 

Components

While purists may dismiss its use of plastic fins, the Maxi Alpha 3 has some clever design features.  The fin unit consists of two plastic rings that go into the ends of a short section of BT-80 and hold the plastic fins in slots.  Two sections of BT-80 form the main airframe, with a short coupler and centering ring that centers the MMT/stuffer tube.  The MMT also glues into the bottom plastic ring.  A plastic nose cone, standard 24mm motor mount with hook, 1/4" launch lugs, and 24-inch plastic parachute complete the kit, which also comes with a big sheet of stick-on decals.

 

Construction

The instructions are reasonable but could stand some updates.  Most importantly, the dimensions for the motor mount are appropriate for a D-length hook, but the current kit comes with an E-length hook and adapter.  The instructions suggest that you have to paint the nose cone, but it's molded in red and would be fine as is.  Estes inadvisably recommends the use of plastic cement for all plastic pieces, but most plastic cement only works on polystyrene, and as far as I can tell, this isn't used in the Maxi Alpha 3.  So I used 5-minute epoxy on all the plastic parts.


The plastic fins in my kit were slightly warped, but I decided to not worry about it and it was no issue in flight.

The original 1979 catalog claimed that you could build and fly the kit in 30 minutes.  Perhaps a slight exaggeration, but it was a simple evening's build.  One nice touch is that the shock cord attaches to the forward centering ring rather than a standard tri-fold.  The down side is that the shock cord is far too short for the kit.  I replaced it with about 4 feet of elastic.

 

Finishing

Built stock, finishing consists of sticking on the decals, no painting required.  The decals didn't appeal to me, so I gave the rocket one coat of white primer and then painted it fluorescent orange, then applied upscaled vinyl Alpha III markings from Stickershock 23.  The red-colored plastic parts were a bit of a liability here as the white primer didn't quite cover the red, but the results were not bad.

Ready to fly, my kit came in at 8.3 ounces.

 

Construction Score: 4

Flight

The model's large size makes packing the chute and a generous handful of dog barf simple.  I flew it twice: once on a D12-3 and once on an E12-4; despite a stiff 15-mph wind, both flights were reasonably straight off a 3' 3/16" rod, and the delays were just about perfect.  (Several larger Estes kits lately, while originally intended for 3/16" rods, have come with 1/4" launch lugs for the newer Porta-Pad E's 1/4" rod.  Despite the looseness of the lugs, it flew fine off the smaller rod.)

Estes recommends the E9-4 and E9-6, and while I expect they would work at least in low-wind conditions, the E12-4 is a safer choice.

 

Recovery

As noted, the stock shock cord is way too short.  The pre-assembled plastic chute is not bad, but I had a shroud line tear out on the first flight.  The 24-inch chute brings the model down slowly, but may cause a bit too much drift on a small field.

 

Flight Rating: 4

Summary

Pros: fast, simple plastic construction; lightweight, flies well on a D12-3.

Cons: instructions need updating; BT-80 tubes are pretty thin; others have complained about fins breaking off on landing, though I didn't have any problems; shock cord too short; plastic parachute somewhat flimsy.

 

Overall Rating: 4
Other Reviews
  • Estes Maxi Alpha 3 By Jon Revelle

    Larger, cooler version of an Estes classic. This thing ROCKS!! I got it for Christmas. I saw it at Ace on December 14,2003 and I can't believe this rocket was still there. It's been OOP for about 3 years. It was a re-release of the original 1979 version. The kit has: 3 BT-80 body t ubes, 2 long and one short 3 red plastic fins 2 rings for holding engine tube, fins and connect ...

  • Estes Maxi Alpha 3 By Dave Russell

    The Maxi Alpha 3 is one of Estes year 2000 re-released limited edition rockets. It is rated Skill Level 2 with a 24mm motor mount. I have seen the price on this kit vary from $15 to $35. It is large version of the Estes classic Alpha kit. Like junior, it is a rather simple build. Stock build utilizes, BT-80 tubes, a 24 inch parachute, little paint (nose only), and pressure-sensitive decals. ...

Flights

comment Post a Comment