LOC/Precision LOC IV

LOC/Precision - LOC IV {Kit} (PK-48) [1985-]

Contributed by Frank Ross

Diameter: 4.00 inches
Length: 47.50 inches
Manufacturer: LOC/Precision
Style: Sport
(Contributed - by Frank Ross - 11/11/00)

Brief:
Up-scaled to 38mm.

Modifications:
For my level-1 certification and my first high-power rocket I wanted a large, simple rocket kit without any bells and whistles. I chose the LOC-IV as I thought it looked to fit the bill, and wouldn't break my credit card. I decided to up-scale to 38mm rather than stick to 29mm because I liked the motor selection and thought I'd get a lot of use out of the 38mm RMS reload set in the future. The modification was pretty straight-forward. I got a heavy duty 38mm cardboard motor tube from a friend (thanks, Dave) and used three, instead of the kit's two, centering rings for the motor mount. I mounted one ring on the fore end of the motor tube, and mounted the other two on either side of the thru-the-wall fin tabs. The kit surprised me when I found that the fin tabs only mount through the airframe wall, and not all the way to the motor mount. I considered cutting new fins with longer tabs but in the end decided to stick with the stock fins. I added three tee nuts to the read C.R. for motor retention with aluminum screen clamps and 8-32 x 1" hex head bolts. I added a stainless u-bolt to the forward C.R. for shock cord attachment. I added a few ounces of lead weight to the nose cone for some additional stability, but later realized that it was unnecessary. Finally, I up-scaled the included 36" chute to a 48" round nylon chute to compensate for added weight and to give a nice, slow recovery for my level-1 attempt.

Overall, I like the LOC kit. Good materials, instructions, and packaging. The only negative would be the short fin tabs. I highly recommend cutting new fins with extended tabs for this kit.

Rocket PicFlight:
The first flight was at SpudRoc-IV for a level-1 cert on a H123W RMS motor. The winds were low and the rocket flew perfectly straight to about 1800' and ejected perfectly at apogee. The rocket drifted quite a distance but landed with hardly a scratch.

The second flight was later the same day on an I357T. The flight was straight but the ejection delay came early and the tubular nylon shock cord zippered the tube about 4". I had also changed back to the 36" parachute to avoid the long walk across the desert to recover the rocket. This however gave too fast a descent rate and one fin broke on impact. I later repaired the zipper by added a tube coupler and a 10" length of 4" airframe tubing. The new LOC-IV-38-stretch added an additional 6" to the overall length.

The third flight was on a H242T, which from simulations looked to be the best motor choice. The winds however were fairly strong and the rocket weathercocked and even though ejection occurred near apogee the rocket had too much horizontal speed and again zippered the tube. The tube was repaired simply by cutting 4" off the recently added repair tube and the rocket is back to close the original length.

The fourth flight was again on a H123W, ejection at apogee, 48" chute but still a rough enough landing to break a fin. The rocket is now repaired and awaiting its next flight.

Summary:
A good, easy up-scale project. Suggestions: Cut new fins with tabs to mount to motor tube. 48" chute a must. Glass tube.

Other Reviews
  • LOC Precision LOC IV By Cody Smith (October 20, 2014)

    This kit was my Junior. Level 1 and I must say it is a beautiful kit. Some people say this rocket is not good for certifications due to the fact that the fins hang below the body. But, unless you land on concrete or desert, these fins are hard to break off. This kit is four-feet tall, four-inches in diameter and, coincidentally, my finished weight was four pounds. I tend to build heavy and ...

  • LOC/Precision LOC-IV By Alex Jordan

    Brief: This is a large single staged, simple mid/high power rocket. It uses parachute recovery and was my first big rocket. Mine came with a 38mm motor mount, although many websites say it has a 29mm motor mount. Also, the fin tabs extend all the way to the motor tube. Construction: The components of this kit came in the typical LOC plastic bag. All of the parts were of the highest ...

  • LOC/Precision LOC-IV By Chris Kiekens

    Brief: An easy to build 3FNC rocket, built for my first shot with a reloadable motor. Construction: The kit contains a 4" kraft paper body tube, two centering rings (plywood) included, nose cone, 36" chute, elastic shock cord, 3 plywood fins, 29mm motor mount, and a 1/4" Launch Lug. This was a really easy kit to build. I spoke to LOC briefly regarding the fins, ...

  • LOC/Precision LOC-IV By Alex Rothchild

    - by Tom Bell  Instructions: The instructions were complete and easy to follow.  Although this is a large rocket, it was not difficult to build. The parts were well manufactured and fit together without problems. This kit was my first large rocket, and it is a good starter kit for large rocketry despite its imposing size.  This kit requires epoxy for assembly of the ...

Flights

comment Post a Comment